16 November 2026
No Hot Water? 7 Common Causes and What to Check First (Perth Guide)

Turned on the tap and got cold water? No hot water is stressful when you’re trying to get ready for work, get the kids washed or keep a rental property running. The good news is that the cause is often one of a handful of things, and a few safe checks can help you work out what to do next.
This guide is for Perth homeowners, renters and landlords, including people in Clarkson, Mindarie, Butler, Merriwa, Quinns Rocks, Ridgewood and Joondalup. It explains what you can check yourself and when to call a licensed plumber or gas fitter.
No hot water: what to check first
Before looking at the hot water system, see whether the problem affects one tap or the whole house. If it’s just one tap, the issue may be with that fixture. If every hot tap is cold, check these things first:
- Electric storage system: Check your switchboard for a tripped safety switch or circuit breaker labelled “hot water” or “HWS”. If it has tripped, you can reset it once. If it trips again, leave it off and call a professional.
- Gas system: Check whether the gas supply is on and whether other gas appliances are working. If they aren’t, there may be a supply issue.
- Continuous flow system: Note any error code on the display before trying anything else.
- Valves and switches: Look for an isolation valve or nearby power switch that may have been accidentally turned off. Don’t force a valve.
- Power outage: Check the Western Power outage tracker for your address. If your electric system uses a controlled-load tariff, ask your retailer whether there could be a supply or switching issue.
If these checks don’t help, avoid opening the unit. The fault may need a licensed trade to diagnose safely.
7 common causes of a hot water system not working

1. Electric storage fault
A tripped safety switch, failed heating element or faulty thermostat can leave an electric storage system with little or no hot water. If you get a brief supply that runs out quickly, an element may not be heating the tank properly.
You can check the switchboard, but don’t open the system’s electrical covers. Repeated trips or work inside the unit require a qualified electrician.
2. Gas storage pilot or ignition fault
On some gas storage systems, the pilot light may have gone out. A faulty thermocouple, gas valve or ignition component can also stop the burner from heating the water. You may notice that the pilot won’t stay lit, or that the system appears to be on but the water stays cold.
You can check whether other gas appliances work. Only try relighting a pilot if the manufacturer’s instructions are clear and you can follow them exactly. If it won’t relight or stay lit, stop and call a licensed gas fitter.
3. Gas supply interruption
A closed supply valve, empty LPG cylinder or interruption to the gas supply can affect a gas storage or continuous flow system. Check whether other gas appliances are working, and check your LPG supply if that applies. Don’t disconnect pipework or try to adjust gas components yourself.
For gas work, use a licensed gas fitter. You can read more about our gas installation and maintenance services.
4. Continuous flow unit fault
A continuous flow system needs power, gas and adequate water flow to operate. An error code, ignition fault, low gas pressure or low flow through a tap can prevent it from firing. Check the display and make sure the unit’s power supply is on; if the code returns, get it checked.
Some units can also reduce output or be affected by frost in cold conditions. A plumber or gas fitter can investigate recurring faults, flow problems or suspected supply issues.

5. Heat pump problem
Heat pumps use a compressor and fan to heat water, so a power supply issue or component fault can leave the tank cold. They also heat more slowly than some other systems, particularly when the weather is cool or the household has used a lot of hot water.
Check the display for a fault code and make sure leaves or stored items aren’t blocking the fan. Don’t remove panels or attempt electrical repairs.
6. Solar booster or control issue
Solar hot water systems often rely on a gas or electric booster when there hasn’t been enough sun. In winter or after overcast days, check whether the booster’s power supply or gas supply is on, and whether the controller is set to allow boosting.
If the controller shows an error, or you still have no hot water after checking the settings, arrange an inspection.
7. Valve problem, leak or ageing system
A faulty tempering valve can cause water to be only lukewarm. A relief valve may release water as part of normal operation, but a constant discharge or leak needs attention. Water around the base of the unit may point to a leaking fitting, or a failed tank. A leaking tank usually needs replacement rather than a patch.
Older systems can also become less reliable, especially if repairs are becoming frequent. A professional can help identify whether the problem is a repairable part or a sign the system is nearing the end of its useful life.
How to relight a gas storage pilot light safely
Only attempt this if your unit’s instructions are available, the steps are clear and there is no smell of gas. Follow the manufacturer’s exact instructions for your model, including any waiting time and control-button sequence. Don’t remove panels, use tools or lean over the burner.
If the pilot won’t light or won’t stay lit after following the instructions, stop and contact a licensed gas fitter. If you smell gas, don’t try to relight it. Turn off the gas supply if you can do so safely, open doors and windows, avoid flames and electrical switches, leave the area if needed, and call your gas network’s emergency line. WA Building and Energy also advises using a licensed gas fitter for gas work; see its gas safety guidance.
What not to do when the hot water stops
- Don’t open the panels on a gas unit or attempt gas repairs.
- Don’t keep resetting a safety switch that trips again.
- Don’t try to repair a tempering valve or leaking relief valve yourself.
- Don’t ignore a puddle around the unit. If it’s safe, keep clear of the water and arrange an inspection.

Repair or replace your hot water system?
Storage systems generally last around 8–12 years, though lifespan varies with the system, water conditions, use and maintenance. Age alone doesn’t decide whether to replace it, but these signs are worth discussing with a plumber:
- Repairs are becoming more frequent.
- Hot water looks rusty or discoloured.
- Energy bills are rising without another clear explanation.
- The tank or its fittings are leaking.
- You’re considering whether continuous flow or a heat pump would suit your household.
A repair may make sense when the fault is limited to a replaceable part and the rest of the system is in reasonable condition. If the tank itself has failed, replacement is usually the practical option. For help with a hot water system repair in Perth, an assessment can clarify the options.
When should you call a plumber?
Call a licensed plumber or gas fitter if the system is leaking, a safety switch trips again, an error code keeps returning, the pilot won’t stay lit, or you can’t identify the cause after the safe checks. Get help promptly if you smell gas, see signs of electrical damage or notice water pooling around the unit.
Plumbing by ET is based in Clarkson and services Perth’s northern suburbs and the wider metro area. Owner Ettienne van Vuuren has more than 12 years’ experience. Plumbing by ET holds Plumbing Contractor Licence PL10986 and Gasfitter Licence GF22932, and weekend callouts are available. For a free, no-obligation quote, call 0424 960 202 or contact Plumbing by ET. For general checks and preventative work, see our plumbing maintenance service.
How long should a hot water system last in Perth?
Storage systems generally last around 8–12 years, but the actual lifespan varies. Leaks, discoloured water or repeated faults are good reasons to ask a plumber to assess the system.
Why is my hot water only lukewarm?
A faulty tempering valve, heating element, thermostat or booster may be limiting the temperature. If it affects the whole house or keeps happening, arrange a professional check.
Can I reset my hot water system myself?
You can check the switchboard and reset a tripped safety switch once, but don’t keep resetting it if it trips again. Follow your unit’s manual for any user-level reset, and don’t open covers or attempt electrical or gas repairs.
Is it cheaper to repair or replace a hot water system?
It depends on the fault, the system’s age and its overall condition. A plumber can explain whether a repair is practical or whether replacement is the better long-term option.
How quickly can a plumber get here?
Plumbing by ET aims to respond promptly, including weekends, and can advise on availability when you call. Timing depends on the location and the work needed.
No hot water can come from a simple supply issue or a fault that needs professional attention. Try the safe checks first, then call a licensed plumber or gas fitter if the problem persists, you find a leak or you’re unsure what to do next.
